Attwood Folding Anti-Glare Boat Navigation Light
Attwood Folding Anti-Glare Boat Navigation Light
Attwood Folding All-Round Anti-Glare Boat Navigation Light
This Attwood Folding Anti-Glare Boat Navigation Light is built to last in the harsh marine environments with its non-corrosive materials and glass-filled polymer bases. It features a fold-down base that allows the light to swing 180° and can be mounted on both horizontal and vertical mounts. All of the wiring is concealed and protected within the pivoting base. In extreme conditions, if a 12ft./lb. force hits the base, the cam lock releases and allows base to swing down, reducing the chance of breakage to the base or pole. With a two mile, 360° light visibility, this anti-glare boat navigation light is for use on boats up to 39.4 ft.
Features:
- Fold-Down Base That Allows The Light To Swing 180°
- All Wiring Is Concealed and Protected Within The Pivoting Base
- Has Two Mile, 360° Visibility
- For Use On Boats Up To 39.4 ft.
- Comes With A 12" Black Plastic Pole
- Built To Last In Harsh Marine Environments
- Can Be Mounted On Both Horizontal and Vertical Mounts
- Non-Corrosive Materials
- Glass-Filled Polymer Base
- Includes a 9-Watt Wedge Base Lamp
- Includes Mounts
Specifications:
- Visibility: Two Mile, 360° Visibility
Installation Instructions
HOW TO INSTALL ATTWOOD FOLDING ALL-ROUND ANTI-GLARE LIGHT
Installation
- Choose a position near the transom that is accessible to wiring and has clearance below deck.
- Place base on the gunwale or deck. At desired location, be sure there I room to rotate the cover. Mark position for the 1-3/8” socket hole.
- Remove base and drill the 1-3/8” diameter socket hole, being careful not to crack the gel coat finish around the hole.
- Fit base into socket hole so it is parallel to boat centerline. Mark position and drill the three screw holes.
- Remove base and connect wires through socket hole. Connect one wire to the battery ground (-). Attach other wire to the 1-amp fused, positive (+) switched wire from the navigation light switch.
- Apply sealant between deck and light base. Fasten base with three #10 stainless steel screws. Do not overtighten screws.
Replacing Light Poles without a Locking Collar
- Align pole screw with slot in the existing base. Insert pole into base.
- Press down firmly to engage electrical connectors.
- To remove pole, pull straight up.
Replacing Light Poles with Locking Collar
- Align pole screw with slot in the base. Insert pole into base.
- Press down firmly to engage electrical connectors.
- Slide locking collar down to base, rotate until you can insert lower ring inside top of base.
- Press collar down into base and rotate until it tightens between pole and base.
- To remove light, rotate locking collar in opposite direction until it loosens, then pull up on pole.
Removing Locking Collar
- For bases that do not accept locking collar, remove screw at bottom of pole. Slide locking collar off end of pole.
- Replace screw in the upper screw hole.
Replacing Bulb
- Unscrew frosted globe counter-clockwise and remove.
- Pull bulb straight up. Replace with #906 9-Watt Wedge Base Replacement Bulb.
- Screw lens clockwise onto pole.
Clean the light with a mild soap and warm water solution. Never use solvents or abrasives that may damage the lens or housing of the light.
California Residents: 
WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov
Need Help Finding the Right Part?
Get real fitment help from a marine business—not a generic marketplace.
Built for the Job. Backed by Drydock.
Order With Confidence
Marine fitment can depend on model, year, serial range, and prior service history. Confirm those details before installation.
Will This Part Fit?
Match the manufacturer part number, engine or drive model, and serial number range before ordering.
- Check the current part number and any superseded numbers
- Verify engine or drive model and serial number
- Send photos when identification is uncertain
Verify before installing.
Compare the removed part, mounting points, electrical connections, and manufacturer numbers before opening sealed packaging or beginning installation.
Quick Specifications
- Brand
- Attwood
- Part Number
- ATT-5358-P12-7
- Product Type
- Boat Navigation Lights
- Availability
- In Stock
- Support
- Fitment help available
Commonly Needed Alongside This Part
Use these quick searches to find related maintenance and installation items. Confirm compatibility before ordering.
Everything You Need Before Ordering
Fitment & Part Verification +
Shipping Information +
Returns & Exchanges +
Warranty Support +
Technical Support +
Why Buy From Drydock Marine?
National e-commerce convenience backed by a real Western New York marine service, propeller, and parts operation.
Let Us Find the Right Part
Send your serial number, model information, and photos. We will help identify the best available option.
